Na de retrofit van de Mor60 EXPAL e

Na de retrofit van de Mor60 EXPAL en tijdens het gebruik van de mortier op de schietstand tijdens de vorming Reco Cie voor 12/13Li zijn er enkele dingen opgevallen.

1. Er is een probleem met verschillende Sights. De regeling is aangepast ter hoogte van de zwaluwstaart. Hierdoor raken ze klem in de ligplaats van de loop of zitten ze soms te los en kunnen ze enkel met de hamer van de lijst B verwijderd worden.
2. De klemband is aangespannen om te vermijden dat deze omhoog schuift tijdens het vuren in de hogere ladingen:
• Dit zorgt vooreerst voor een moeilijkheid om de klemband los te maken. Dit moet nu met beide handen gebeuren waardoor de Mortier loop niet kan ondersteund worden. Er werd bij verschillende stukken een touw gebruikt om de klemband te kunnen openen omdat dit manueel nagenoeg onmogelijk is.
• Bij het vuren met de munitie ILL Vis (IMI) kwamen er verschillende bommen vast te zitten ter hoogte van de klemband. Dit kan enkel opgelost worden door herhaaldelijk te slaan met een hamer. Deze dril is voorzien in geval er vocht rond de obturator van de munitie zit en de lucht niet kan ontsnappen. Ik vermoed echter dat het te wijten is aan het aanspannen van de klemband en het zeer licht vervormen van de buis.
• Voor de ILL doet dit zich voor bij 30% van de bommen die geladen werden (12/32).
• De mensen van SIA (Adjt Jardon) hadden reeds gemerkt tijdens testen met hun kalibers dat er bij verschillende stukken een probleem was. Zij hebben tekst en uitleg gevraagd aan de firma.

BLUF:
Het aanspannen van de klemband bemoeilijkt de manipulaties op het stuk. Bij sommige stukken is de klemband zo erg aangespannen dat het nagenoeg onmogelijk is om deze te openen. Als er haperingen ontstaan tijdens het laden als gevolg van het aanspannen van de klemband, moet dit volgens onze cel zo snel mogelijk worden opgelost.

Resultaten (Engels) 1:

After the retrofit of the EXPAL and Mor60 while using the mortar on the shooting range during the formation Reco Cie for 12/13Li there are some things noticed. 1. There is a problem with different Sights. The scheme has been modified at the height of the swallow tail. As a result, hitting they clamp in the location of the course or they are sometimes too loose and they can only be removed with the hammer of the list B. 2. the clamp is tightened to avoid this slide during firing up in the higher loads: • This will first of all for a difficulty to the conveyor. This should now be done with both hands making the mortar course cannot be supported. It was at different pieces a rope used to open the clamp band because this manual is almost impossible. • When firing with the ammo ILL fish (IMI) there were several bombs stuck at the height of the conveyor. This can only be solved by repeatedly hitting it with a hammer. This drill is provided in case there is fluid around the obturator of the ammunition and the air cannot escape. However, I suspect that it is due to the tightening of the clamp band and distort the very light of the tube. • For the ILL does this occur at 30% of the bombs were loaded (12/32). • The people of SIA (Adjt Jardon) had already noticed during testing with their jigs that different pieces was a problem. They have asked an explanation to the company. BLUFF: Tightening of the clamp band complicates the manipulations on the piece. In some pieces is the conveyor so very filed that it is almost impossible to open it. If there are hitches occur during loading as a result of the tightening of the clamp band, this should be solved as soon as possible according to our cell.

Resultaten (Engels) 2:

After the retrofit of the Mor60 EXPAL and while using the mortar to the shooting range during the formation Reco Cie 12 / 13Li there have noticed a few things. 1. There is a problem with different Sights. The scheme has been adjusted at the height of the dovetail. As a result they become stuck in the barrel berth or are they too loose and sometimes they can be removed only by the list of B hammer. 2. The clamp is tightened to prevent it from moving upwards during firing in the higher loads: • This firstly creates a difficulty to release the clamp. This must happen now with both hands, causing the mortar barrel can not be supported. By using a rope with different pieces to open the clamp band because it is almost impossible manually. • When firing the ammunition ILL Fish (IMI) came stuck several bombs at the height of the clamp. This can only be solved by repeatedly hitting it with a hammer. This drill is provided in case there is moisture around the obturator of the ammunition and the air can not escape. However, I suspect that it is due to the contraction of the clamping band and the very slightly deforming the tube. • For the ILL does this occur in 30% of the bombs that were loaded (12/32). • The people of SIA (Adjt Jardon) had already noticed during testing by their calibers that there was a problem in several pieces. They explanation requested from the company. BLUFF: The tightening of the clamp complicates manipulations on the piece. Some pieces of the clamp is tightened so much that it is almost impossible to open it. If there are glitches occur during the loading as a result of tightening of the clamping band, this in accordance with our cell has to be solved as quickly as possible.

Resultaten (Engels) 3:

after the retrofit of the mor60 expal and during the use of the mortar on the range during the formation of 12 / 13li reco cie, there are a few things to notice.

1. there is a problem with different sights. the system is adapted to the level of the dovetail.will they get stuck in the berth of the course, or are they sometimes to go with the hammer and can only be removed from the list b.
2. the clip is brought up in order to avoid the slide during the fire in the higher charges: "this is the first of a difficulty to the clip.this must happen with both hands and the mortar barrel can be supported. there were several pieces used a rope to the clip to open because this manual is almost impossible. "the fire with the ammunition ill fish (imi) there were several bombs stuck at the level of the clip.this can only be solved by repeatedly hitting it with a hammer. this drill is provided in case of fluid around the obturator of ammunition and the air can't escape. however, i suspect that it is due to the action of the clip and the very light deformation of the tube. "for the ill do it for 30% of the bombs were loaded (12 / 32).
the people of sia (adjt jardon) had already noticed during testing with their calibers that several pieces was a problem. they have an explanation to the firm. bluff:


the commencement of the clip on the complicated manipulations. in some parts of the clip is brought so much that it is almost impossible to open.if problems arise during loading due to the commencement of the clip in our cell, it must be solved as soon as possible.